Two cartridges can carry carbon from the same activation batch and still behave nothing alike. One holds the carbon as a pressed block, the other as a bed of loose granules.
The difference shows up in three places: pressure drop, contact time and how the cartridge fails at end of life. Buyers who compare only the carbon grade usually miss all three.
What Granular Carbon Does Differently
Granular activated carbon sits between a rigid PP shell and inner non-woven layers. Water passes through the bed rather than through a wall of bonded carbon.
The open flow path between granules drops less pressure at the same flow rate. It also gives a longer residence time per centimetre of cartridge than a dense block.
The weakness is mechanical. Granules can settle, migrate or escape as fines if the retention layer is thin or poorly bonded.
That is why a granular cartridge is judged by its shell and its non-woven interlayer as much as by its carbon. A well-built UDF cartridge should not produce black water on first wetting.
Flow direction inside the cartridge is radial in most designs. Water enters the outer annulus and moves inward through the bed toward the core.
Radial flow keeps the path short and the pressure drop low. It also means the outer layer loads first, so a granular cartridge shows its sediment history from the outside in.
Commissioning deserves two or three litres of flush. Granular beds can carry fine carbon from the filling line, and the first draw is not representative of steady-state performance.
Pressure Drop and Contact Time: The Real Trade-off
Numbers below are working ranges for 10 inch cartridges at about 1 GPM. They shift with water temperature, inlet pressure and sediment load.
| Cartridge type | Pressure drop at 1 GPM | Contact time | Sediment tolerance |
|---|---|---|---|
| 10 inch GAC, smooth shell | 0.1–0.2 bar | High | Low |
| 10 inch block, 5 micron | 0.2–0.4 bar | Medium | Medium |
| 10 inch block, 1 micron | 0.4–0.7 bar | Medium | High |
| 20 inch GAC | 0.1–0.2 bar at 2 GPM | High | Low |
Read the table as a design input rather than a ranking. A gravity-fed or low-pressure system cannot afford the block at 1 micron. A membrane train cannot afford the sediment that passes a granular bed.
Where GAC Wins
Low-pressure and gravity-fed installations are the clearest case. Available head is small, so every tenth of a bar matters.
- Tea shops, coffee machines and beverage dispensers, where flow stability shows in the cup.
- Municipal water with low turbidity but noticeable chlorine or odour.
- Systems with a downstream membrane that already has adequate sediment protection.
- Retrofit jobs where the existing pump has no spare pressure margin.
Flow stability is the commercial argument here. Baristas and shop owners notice a cartridge that halves output before its rated capacity is reached.
Tea and coffee equipment adds a second constraint. Softened or low-hardness water passes a granular bed quickly, so the carbon does the work without a scale layer closing the surface.
Where the incoming water is already filtered, GAC also removes the taste of the treatment itself. Chlorine dioxide and chlorite give a medicinal note that a low-pressure bed handles better than a tight block.
Where a Block Wins
Reverse osmosis pre-filtration is the standard answer. The block retains sediment that would otherwise foul the membrane surface.
Intermittent supply and high turbidity favour the block for the same reason. A granular bed passes a slug of rust or silt straight through to whatever sits behind it.
Vertical installations with vibration also suit blocks. A settled granular bed can channel, and channeling means untreated water reaches the outlet long before the capacity is used up.
Choosing the Media: Coconut or Coal
Coconut shell carbon carries a finer micropore structure. That suits chlorine, taste and odour work and reaches higher iodine values.
Coal-based carbon spreads its pore volume into mesopores. It holds up better against larger organic molecules and usually costs less per cartridge.
For household drinking water at low organic load, coconut is the common choice. For cost-driven replacement programmes on clean municipal supply, coal is defensible.
Both are available in the same shell, which is why the media grade belongs on the purchase order and not only in the catalogue description.
Cost differences between the two media are modest at cartridge level and larger at programme level. On repeat orders, a coal-based grade can cut unit cost by a visible margin on volumes where chlorine load is low year round.
Batch consistency matters as much as the grade itself. Iodine value that drifts between deliveries shows up as uneven service life in the field, and the cause is rarely traced back to the carbon.
Failure Signs That Point Back to the Cartridge
- Black water on commissioning — fines escaping past the retention layer.
- Early chlorine breakthrough — channeling through a settled bed.
- Sudden drop in pressure drop — bed movement or a bypass at the end cap.
- Carbon granules in the downstream housing — a failed end seal, not a carbon problem.
None of these appear in a chlorine test taken on the first day. They surface at week six, when the replacement has already been ordered.
Frequently Asked Questions
Will a GAC cartridge remove chlorine completely?
At adequate contact time it removes free chlorine to below taste threshold. At high flow through a short bed it reduces chlorine instead of eliminating it.
Can a granular cartridge be installed horizontally?
Yes, provided the shell is rigid and the retention layer is bonded along the full length. Horizontal mounting without those two conditions encourages settling at one end.
Does iodine value matter as much for GAC as for block?
It still indicates micropore volume, so it matters for chlorine duty. For organic removal the pore size distribution says more than the iodine number alone.
What flow should a 10 inch GAC cartridge run at?
Around 1 GPM is the usual household figure. Above roughly 1.5 GPM, contact time shortens and chlorine breakthrough arrives early.