CTO is the label printed on more carbon cartridges than any other, and it is also the one buyers question most. The letters describe an intended duty, not a construction method. Two cartridges marked CTO can differ completely inside.
That gap matters when a specification is written by copying a competitor catalogue. This guide covers what the label means, how a compressed block is built, and which numbers on the sheet actually predict performance.
What CTO Stands For in a Cartridge Spec
CTO is an abbreviation for chlorine, taste and odour reduction. It is a performance class, not a material grade and not an end-cap style.
A CTO cartridge is expected to remove free chlorine and the taste and smell that come with it. How it does that is left open by the label.
- Compressed carbon block — rigid, high surface area, good sediment retention.
- Sintered carbon block — carbon fused onto a PP substrate, very low fines.
- Granular bed — loose carbon between non-woven layers, lower pressure drop.
A purchasing spec that says only "CTO" therefore specifies almost nothing. Add iodine value, micron rating, end-cap geometry and flow rate before comparing quotes.
How a Compressed Block Is Actually Made
Coconut shell carbon is ground, screened and blended with a polypropylene binder. The blend is pressed into a sleeve around a PP core and then cured.
Sintered blocks take a different route. Carbon granules are fused onto a PP substrate at elevated temperature, so the body holds together without a separate binder phase.
Both routes produce a rigid cylinder that will not fluidise under flow. Pore size is set by the grind and the press density, not by a downstream filter.
This is why micron rating and iodine value move independently. A tight grind gives a low micron rating and also lowers flow, because the same wall must pass water through smaller openings.
Wall thickness is the third variable and the least visible on a datasheet. A thicker wall buys adsorption capacity and sediment depth, then takes it back in flow. Two cartridges at 2.5 inch outside diameter can still differ by several millimetres of wall.
In large-volume production, wall thickness is held by press tooling rather than by the operator. That is the reason a new tool costs money up front and then holds the same geometry for hundreds of thousands of pieces.
Housing clearance deserves a check before ordering. A 20 inch block with a thick end gasket can bind in a housing that accepts a thin one. The resulting bypass looks exactly like a failed cartridge.
Iodine Value, Micron Rating and End Caps
Iodine number is measured by ASTM D4607 and used as a proxy for micropore surface area. Higher values mean more adsorption sites per gram, within limits.
For drinking water blocks, 900 to 1100 mg/g is the working range. A 1300 mg/g block is not automatically better; very high activation can soften the body and increase fines.
Micron ratings on the site catalogue run from 5 micron down to 1 micron, with 0.5 micron available on request. Expect pressure drop to climb as the rating tightens.
| Parameter | Typical range | What it controls |
|---|---|---|
| Iodine number (ASTM D4607) | 900–1100 mg/g | Chlorine and organics capacity |
| Micron rating | 5 / 1 / 0.5 micron | Particle retention and pressure drop |
| Outer diameter | 2.5 inch standard | Housing fit, wall thickness |
| Length | 10 and 20 inch | Contact time and capacity |
| End cap | DOE, single open end | Flow path and housing compatibility |
End-cap choice is often decided by the housing rather than by performance. Double open end suits standard household housings with two gaskets. A single open end with a 222 or flat gasket forces water through the wall instead of letting it bypass the end face.
Where the Block Sits Inside an RO System
A three-stage drinking water system usually runs sediment, then carbon block, then membrane. A fourth post-carbon stage polishes taste at the tap.
The block protects the membrane. Thin-film composite membranes are sensitive to free chlorine, and oxidation damage is permanent rather than reversible by cleaning.
Upstream PP sediment protects the block in return. Running a block without sediment pre-filtration shortens its life and hides the cause, because the block loads from the inside out.
Ten inch cartridges dominate under-sink systems. Twenty inch blocks appear in light commercial pre-treatment and on skids feeding a larger membrane array.
Sizing begins with flow, not with length. A 10 inch block is comfortable near 0.5 to 1 GPM; pushing 2 GPM through it costs pressure and shortens the life of the carbon.
Parallel installation is the usual answer when demand exceeds a single cartridge. Two blocks in parallel halve the face velocity at the same total flow, which recovers pressure drop without changing the housing model.
Chlorine testing should be done at the outlet, not at the tap after a carbon post-filter. A post-carbon cartridge can mask breakthrough upstream for weeks and make a spent block look serviceable.
Limits Worth Planning Around
A standard CTO block handles free chlorine well and chloramine poorly. Utilities that switch to chloramine need catalytic carbon or a longer contact time.
Dissolved contaminants are a different problem. Lead, nitrate and arsenic require media certified under NSF/ANSI 53 scope, not a CTO block with a tight micron rating.
Temperature is a quiet constraint. Water above roughly 38 °C softens the binder and can shorten service life in hot-water lines.
New cartridges should be flushed before use. Two to three litres removes manufacturing fines and prevents a grey first draw that looks like a defect.
Frequently Asked Questions
Is CTO the same as a carbon block?
Not strictly. CTO names the duty, carbon block names the construction. Most CTO cartridges are blocks, but granular CTO cartridges exist and behave differently under flow.
Does a CTO carbon block remove lead?
No, not at levels that matter. Lead removal depends on certified media inside a cartridge tested to NSF/ANSI 53, and the standard scope defines what may be claimed.
How often should a CTO block be replaced?
Three to six months is typical for household duty. Replace sooner when pressure drop doubles against a new cartridge, or when flow falls by roughly a third.
Can a 0.5 micron block be supplied?
Yes, by tightening the grind and press density. The trade-off is lower flow at the same inlet pressure, so the housing and pump margin should be checked first.